ROVANATRADE

Cable Tray and Ladder Specifications: Sizes, Materials and Finishes

Cable tray and ladder specifications explained: dimensions, steel thickness, materials, galvanizing, supports and technical documents for project supply in Egypt.

Cable tray and ladder specifications cover system type, width, side height, material thickness, section length, finish, supports and fittings. Defining these together helps customers compare supply proposals and communicate the intended product clearly.

This guide explains the information to specify, then shows how to organise it into a technical submittal for project review.

Cable tray specification checklist

ItemInformation to specify
System typePerforated tray, solid-bottom tray, ladder or wire mesh
DimensionsWidth and side height with units
MaterialMetal type and required grade
ThicknessRequired base material thickness and measurement basis
Section lengthRequired straight-section length
FinishPre-galvanized, galvanized after fabrication, painted or specified system
Supports and loadingCable weight, support arrangement and fixing details
AccessoriesBends, tees, joints, covers and special fittings

Cable tray sizes: width, height and thickness

Keep width, side height and thickness distinct. An illustrative quotation request might state 300 mm wide × 50 mm side height × 1.5 mm steel thickness. This demonstrates how to describe a size; suitability still depends on the cables, load and design.

Use a consistent dimension order in drawings and quantities. For selecting route width from cable information, read our cable tray sizing and cable layout guide.

We prefer 3-metre straight sections for suitable supply requirements, with the requested length stated explicitly. Section length is different from support spacing. See the 3-metre tray section guide.

Thickness and cable ladder specifications

Review thickness together with section geometry, loading and support arrangement. A thicker sheet alone does not establish system suitability. For ladder, also define side rails, rungs, their dimensions and spacing, and joint and fitting details.

For straight-route planning, we use 1.5-metre support spacing, subject to checking load, section, fixing and approved details. Fittings and branches require their own support review. See our cable tray support spacing guide.

Specify galvanizing or coating clearly

Identify whether the proposed product uses pre-galvanized sheet, hot-dip galvanizing after fabrication, powder coating or a combined system. Review the selection against the service environment and project specification, including protection requirements for components and joints.

Read the galvanizing comparison and steel sheet grades guide for more detail.

How specifications affect the price per metre

Compare prices for matching width, height, thickness, material and finish. Establish whether joints, covers, transport and installation are included. A difference in scope may make two headline prices unsuitable for direct comparison.

Our cable tray prices in Egypt guide explains quotation factors. Send the selected specifications and quantities for a project-specific proposal.

From product specifications to technical approval

Once the proposed product is defined, its data, drawings and required evidence can be assembled into a project submission. The following sections explain how to organise that package and respond to review comments.

What is a technical submittal?

A technical or material submittal is a set of documents presented for review against project requirements. Depending on the project, it may include product data, drawings, a compliance schedule and requested supporting evidence.

It serves a different purpose from a quotation. The quotation defines commercial terms and supply scope, while the technical submission identifies the proposed product. Check that the two agree on materials, dimensions and finishes.

Start with the project item and specification

Gather the relevant bill-of-quantities item, specification, drawings and latest review comments. Identify whether the item is perforated tray, solid-bottom tray, ladder or wire mesh containment, and link each product to its size and application.

Avoid submitting an unmarked general catalogue. Highlight the proposed selection and relevant pages. Where alternatives exist, distinguish the actual proposal from options that still need a decision.

Our cable tray quotation checklist can help organise the initial request.

Product data and drawings

Product data should describe the proposed type, material, finish and dimensions. Component drawings should show the relevant section, openings, connections and accessories. As an example of how such information can be organised, Eaton's specification includes a Submittals section addressing product data and drawings of accessories and supports. See the Eaton cable tray specification.

Distinguish component drawings from route drawings. Component drawings describe the product; route drawings locate the system within the project. Establish the required scope and the party responsible for each document.

For ladder, check that side-rail, rung and joint information describes the proposed assembly. For tray, review the section, width, side height, thickness and supplied length. Our tray versus ladder guide explains the product distinction.

Build a traceable compliance schedule

Rather than placing an unsupported “complies” against every requirement, use a schedule that helps the reviewer locate the evidence:

ColumnSuggested information
Requirement referenceSpecification item or page
Project requirementRequired material, dimension, finish or document
Proposed productThe specific selection submitted
Supporting referenceRelevant page, drawing or report
RemarksAny deviation or information still outstanding

Adapt this suggested layout to the consultant's form. The purpose is to make differences visible and traceable.

Review certificates and test reports carefully

Where a certificate or report is required, review the issuing body, scope, date and covered product. A quality-management certificate is different from a load-test report for a particular section. Listing a standard in a catalogue does not by itself demonstrate that every size has been tested.

For requested loading information, the conditions and applicability must be clear enough to compare with the design requirement. Do not infer section capacity from thickness alone or from a product photograph.

State required documents in the initial enquiry so their availability and applicability can be reviewed. Any additional action needed before material approval can then be identified early.

Responding to consultant comments

Maintain a comment sheet recording each observation, the response, the revised location and the new revision number. If a point remains open, identify its status rather than resubmitting an unchanged package without explanation.

For example, a request to clarify the support finish may require updating the support data sheet, compliance schedule and comment response together. Leaving conflicting descriptions elsewhere creates further uncertainty.

Use consistent submission numbers, revisions and dates across the cover, index and drawings. Interpret review codes according to the project's own procedure; identical labels do not necessarily carry identical meanings across projects.

Final checks before submission

  • Confirm project name, item reference and revision.
  • Identify the proposed product clearly in data sheets and drawings.
  • Check consistency of material, thickness, dimensions and finish.
  • Include required supports, joints and special fittings.
  • Provide appropriate evidence for technical claims where required.
  • Show deviations, outstanding points and responses to previous comments.
  • Check agreement between Arabic and English versions where both are submitted.

Preparing an enquiry with Rovana Trade

Send the specification, quantities, drawings, submission requirements and any consultant comments to Rovana Trade, together with the required material dates. This allows the proposed product and requested documentation to be reviewed before agreeing the manufacturing and delivery arrangements.

Rovana provides supply and installation of its products within an agreed scope. Explore our manufacturing process guide and supply and installation service, or send your enquiry through the contact page.

After completing the project's review procedure, retain the reference revision for comparison during site receiving inspection.

Was this article helpful?

Your feedback helps us improve our explanations and information.

Choose your answer

Comments are for internal review and are not public. Maximum 1,000 characters; please avoid personal information.

Send us your BOQ and get a quotation the same day

A bill of quantities, drawings or even a photo from site — our technical team reviews it and replies.

Chat on WhatsApp